Site Overlay

ADC0808 DATASHEET PDF

ADC IC details, pinout & PDF of Datasheet. It is an 8 bit analog to digital converter with eight input analog channels. The ADC IC is a commonly used ADC module for projects were an external ADC is Find ADC pin diagram, features & datasheet. tiplexer with common output (sample/hold port) see. ADC data sheet. (See AN for more information.) Features n Easy interface to all microprocessors.

Author: Dot Mazuran
Country: Cayman Islands
Language: English (Spanish)
Genre: Literature
Published (Last): 22 February 2008
Pages: 293
PDF File Size: 2.77 Mb
ePub File Size: 5.46 Mb
ISBN: 173-4-70401-627-4
Downloads: 90256
Price: Free* [*Free Regsitration Required]
Uploader: Mutaur

End of Conversion EOC. What is Web Browser. Hence, if you are looking for a ADC module with a decent resolution of 8-bit that could measure up to 8 channels then this IC is for you. Start conversion; input pin; a low to high pulse is given. The obtained value is 2.

National Semiconductor

Digital output bit 4. Has to be given clock signals 0V-5V 20Mhz approx. Interface GPS with Arduino.

Output 2 -1 to 2 When the conversion is complete the EOC pins goes low to indicate the end of conversion and data ready to be picked up. Step size is the change in analog input to cause a unit change in the output of ADC. These three bits have to be set as shown in the table below to access the respective analog fatasheet.

  KICKER KX600.1 PDF

Analog Channel 1 to 5.

ADC Datasheet(PDF) – National Semiconductor (TI)

This is an output pin which goes high once the conversion is over. Has to be made high to get output on output pins.

The default step size is Choosing Motor For Robots. Skip to main content. SPI Module of Arduino. Interface SD Card with Arduino. Connect to ground of the circuit.

Once the channel is set it should be enabled by making the Address latch enabled ALE pin to go high momentarily.

End of conversion; output pin; goes low when the conversion is over. Since the ADC IC can measure up to eight Analog voltage and also does not have an internal clock slightly requires more components to make it work compared to its predecessor ADC In the above circuit I have used a potentiometer to feed in a variable voltage of 0V to 5V to the IN1 pin and the present Voltage is read using a voltmeter.

This pin is should be temporarily made high to select ADC channel.

ADC is an 8 bit analog to digital converter with eight input analog channels, i. This is an input pin which is made high to start conversion.

National Semiconductor – datasheet pdf

Arduino based GPS receiver. The input which is to xatasheet converted to digital form can be selected by using three address lines. This high-density System-in-Package SiP integrates controller, power switches, and support components.

  ALISTAIR MACLEAN SEAWITCH PDF

These three pins dstasheet used to select the channel. Powers adc088 IC typically with 5V. Choosing Battery for Robots. It is a pin Eight channel 8-bit ADC module. As you can see in the image the voltage value is 2. TL — Programmable Reference Voltage. Vref is connected to ground normally. Output digital pins which gives the result of the ADC conversion. That is for every increase of Virgin Galactic — Commercial Space Flight. The ADC needs some specific control signals for its operations like start conversion and bring data to output pins.

Submitted by admin on 13 October The right input analog voltage can be given to pins datqsheet IN1 to IN7, but the IC can read the voltage of only one channel at a time. Or even to use as a standalone ADC module. These 7 pins are the input pins for Analog voltage sensor.

The step size is decided based on set reference value. Clock input; to provide external clock. Input pin; a low to high pulse brings data to output pins from the internal registers at end of datashert.